EN 16062 EUROPEANSTANDARD NORME EUROPEENNE EUROPAISCHE NORM August 2023 ICS 03.220.20; 13.200; 35.240.60 Supersedes EN 16062:2015 English Version Intelligent transport systems - ESafety - eCall high level application requirements (HLAP) using GSM/UMTS circuit switched networks Systemesdetransportintelligents-ESafety IntelligenteTransportsysteme-ESicherheit Exigencesdeprotocoled'applicationdehautniveau Anforderungen an High-Level-Anwendungsprotokolle (HLAP) relativesa I'eCallvia des réseaux commutésde fur eCall (HLAP) unter Verwendung von geschalteten circuits GSM/UMTS GSM/UTMS-Netzwerken This European Standard was approved by CEN on 24 July 2022. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status ofa national standard without any alteration.Up-to-date lists and bibliographicalreferences concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by Centrehasthe same statusasthe official versions. CENmembers are thenational standards bodies of Austria, Belgium,Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany,Greece,Hungary,Iceland,Ireland,Italy,Latvia, Lithuania, Luxembourg,Malta, Netherlands,Norway, Poland,Portugal, Republic ofNorthMacedonia,Romania, Serbia,Slovakia,Slovenia,Spain, Sweden,Switzerland,Turkiyeand United Kingdom. cen EUROPEAN COMMITTEE FOR STANDARDIZATION COMITE EUROPEENDE NORMALISATION EUROPAISCHES KOMITEE FUR NORMUNG CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels @2023CEN All rights ofexploitation inanyformandbyanymeans reserved Ref. No.EN 16062:2023 E worldwideforCENnational Members. EN 16062:2023 (E) Contents Page European foreword. Introduction .. 5 1 Scope..... 2 Normative references. 3 Terms and definitions ... .8 4 5 Conformance.. .12 6 General overview of the eCall transaction for Pan European eCall ..14 7 Requirements . 7.1 General requirements .. .18 7.1.1 General.. ..18 7.1.2 7.1.3 Enabled PSAP.. .18 7.1.4 IVS configured only for eCall.. ..18 7.1.5 7.1.6 Standby mode applicable to IvS configured for eCall only .19 7.2 Activation.... ..19 7.2.1 7.2.2 Activation of a test eCall... ..20 7.3 Call set-up.. ..20 7.3.1 General...... 7.3.2 IVS network access device (NAD) already registered on PLMN . ..20 7.3.3 eCall in progress... .20 7.3.4 Network selection and registration..... 7.3.5 Authentication of the subscriber... .21 7.3.6 eCall establishment.. 21 7.3.7 Cell localization (by network) .. 7.3.8 Manual termination of eCall by vehicle occupants before trigger confirmation .. ...22 7.4 MSD transfer .. .22 7.4.1 General.... ..22 7.4.2 Send initiation signal from IVS eCall modem to PSAP.. .23 7.4.3 eCall modem synchronization.... 7.4.4 Request MSD by PSAP eCall modem to IVS eCall modem.. 7.4.5 Send MSD from vehicie IVS to PSAP eCall modem.. .24 7.4.6 Link layer error check..... 7.4.7 Linklayer ACK from PSAP eCall modem to IVS eCall modem .... .24 7.5 Application layer acknowledgement (AL- ACK)... .25 7.5.1 Following transmission of the MSD to the eCall PSAP application.... 7.5.2 PSAP acknowledges the MSD... 25 7.5.3 No receipt of application layer ACK.. .25 7.5.4 Form of presentation of the AL.-ACK.... 7.6 PSAP request"SEND MSD" 27 7.6.1 General.... 27 7.6.2 2 EN 16062:2023 (E) 7.6.3 After call clear-down ... 29 7.7 (void) .29 7.8 Audio link to vehicle occupants.... 29 7.9 eCall clear-down.... 29 7.10 PSAP call back... .30 7.11 Rerouting to another PSAP/emergency control centre. 30 7.12 Handling non equipped situations / error cases .. 31 7.12.1 MSD not transmitted correctly 31 7.12.2 Network registration fails ... 31 7.12.3 Call failure before the MSD is sent and acknowledged 31 7.12.4 Mobile network not supporting eCall flag or not provided with routing tables. 31 7.12.